1. Refer to the exhibit. What does the “O*E2″ from the “O*E2 0.0.0.0/0 [110/1] via 192.168.1.1, 00:05:34, Serial0/0″ line represent?
• an external OSPF route that will not increment in cost.

2. Refer to the exhibit. What is the cost of the route to the 10.0.0.0 network?
• 1786

3. What three parameters must be indentical between OSPF routers in order to form an adjacency? (Choose three.)
• area id
• hello interval
• network type

4. What does OSPF use to reduce the number of exchanges of routing information in networks where large numbers of neighbors are present? (Choose two.)
• designated router
• backup designated router

5. What does OSPF use to calculate the cost to a destination network?
• bandwidth

6. A fully converged five router OSPF network has been running successfully for several weeks. All configurations have been saved and no static routes are used. If one router looses power and reboots, what information will be in its routing table after the configuration file is loaded but before OSPF has converged?
• Routes for connected networks that are operational will be in the routing table.

7. Refer to the exhibit. Router A is correctly configured for OSPF. Which OSPF configuration statement or set of statements was entered for router B to generate the exhibited routing table?
• B(config-router)# network 192.168.1.0 0.0.0.3 area 0

8. Refer to the exhibit. Which network command or set of sommands will cause OSPF to be enabled to send and receive packets for any R1 interface in the exhibited subnets?
• R1(config-router)# network 0.0.0.0 255.255.255.255 area 0

9. Refer to the exhibit. What does the “2″ stand for in the router ospf 2 statement?
• The number 2 identifies this particular instance of OSPF on this router.

10. Refer to the exhibit. All routers have been configured with the interface priorities that are shown. All routers were restarted simultaneously. The results of the DR/BDR election are shown. What can be concluded about this network?
• The highest router ID was most likely determined via an OSPF router-id statement or statements.

11. Refer to the exhibit. What configuration statements would give the results that are shown in the output of the show ip protocols command?
• B(config)# router ospf 1B(config-router)# router-id 192.168.1.5

12. Refer to the exhibit. How many OSPF adjacencies must be formed to build the complete topology if a DR or BDR were not elected in this OSPF network?
• 6

13. What is the default administrative distance for OSPF?
• 110

14. Refer to the exhibit. Routers A, B, C, and D are all running OSPF with default router IDs and OSPF interface priorities. Loopback interfaces are not configured and all interfaces are operational. Router D is the DR and router C is the BDR. What happens immediately after the following commands are entered on router A?
• A(config)# interface fa0/0
A(config-if)# ip ospf priority 255
D will remain the DR. C will remain the BDR.

15. Refer to the exhibit. All routers are running OSPF. What cost would JAX put in its routing table for the 10.0.0.0/24 network?
• 1787

16. What range of networks will be advertised in the OSPF updates by the command Router1(config-router)# network 192.168.0.0 0.0.15.255 area 100?
• 192.168.0.0/24 through 192.168.15.0/24

17. Refer to the exhibit. The network administrator wants to set the router ID of Router1 to 192.168.100.1. What steps must the administrator take to accomplish this?
• nothing, the router-id of Router1 is already 192.168.100.1

18. Refer to the exhibit. When OSPF is operational in the exhibited network, what neighbor relationship is developed between Router1 and Router2?
• A FULL adjacency is formed.

19. Refer to the exhibit. Assuming that the routers have default interface OSPF priorities and no configured loopback interfaces, what two roles will router B play on each network segment? (Choose two.)
• DR for network 192.168.1.200
• BDR for network 192.168.1.204

20. Refer to the exhibit. Router1 and Router2 are running OSPF. The show ip ospf neighbor command reveals no neighbors. What is a possible cause?
• OSPF hello or dead timers do not match

21. Refer to the exhibit. Which command sequence on RouterB will redistribute a gateway of last resort to the other routers in OSPF area 0?
• RouterB(config)# ip route 0.0.0.0 0.0.0.0 172.16.6.6
RouterB(config)# router ospf 10
RouterB(config-router)# default-information originate

22. Refer to the exhibit. RouterA, RouterB, and RouterC in the diagram are running OSPF on their Ethernet interfaces. Router D was just added to the network. Routers are configured with the loopback interfaces (Lo 0) that are shown in the exhibit. What happens to the OSPF DR/BDR after RouterD is added to the network?
• There is no change in the DR or BDR until either current DR or BDR goes down.

23. Which two statements describe the use of OSPF DR/BDR elections? (Choose two.)
• Elections are required in broadcast multiaccess networks.
• Elections are required in non-broadcast multiaccess networks.

24. Refer to the exhibit. The routers in the exhibit are using default OSPF configuration settings to advertise all attached networks. If all of the routers start at the same time, what will be the result of the DR and BDR elections for this single area OSPF network? (Choose three.)
• Router A will be DR for 10.4.0.0/16.
• HQ will be BDR for 10.4.0.0/16.
• Remote will be DR for 10.5.0.0/16.

25. Refer to the exhibit. What must be received between neighbors to prevent the dead time that is shown in the exhibit from reaching zero?
• hello packets

1. Refer to the exhibit. When Router D is configured to use a link-state routing protocol and is added to the network, what is the first thing that it does to begin learning the network topology?
• It learns about its directly connected networks when its interfaces reach the up state.

2. What two events will cause a link state router to send LSPs to all neighbors? (Choose two.)
• whenever the network topology changes
• upon initial startup of router or routing protocol

3. What is the final step in the link state routing process?
• SPF computes best path to each destination network

4. What two statements correctly describe the link state routing process? (Choose two.)
• each router in the area floods LSPs to all neighborsall routers in the area have identical link state databases.

5. Refer to the exhibit. What kind of information would be seen in an LSP sent from router JAX to router ATL?
• cost of the link

6. What feature do modern link-state protocols provide to minimize processing and memory requirements?
• splitting routing topologies into smaller areas

7. To achieve network convergence, what three steps does each link state router take? (Choose three.)
• build a Link State Packet (LSP) containing the state of each directly connected link.
• flood the LSP to all neighbors, who then store all LSPs received in a database.
• construct a complete map of the topology and compute the best path to each destination network.

8. What speeds up convergence in a network using link-state routing?
• updates triggered by network changes

9. Why is it difficult for routing loops to occur in networks that use link-state routing?
• Each router builds a complete and synchronized view of the network.

10. What are some of the advantages of using a link-state routing protocol instead of a distance vector routing protocol? (Choose two.)
• Routers have direct knowledge of all links in the network and how they are connected.
• After the inital LSA flooding, they generally require less bandwidth to communicate changes in a topology.

11. Which algorithm is run by link-state routing protocols to calculate the shortest path to destination networks?
• Dijkstra

12. Refer to the exhibit. Which statement correctly describes the path traffic would take from the 10.0.0.0/24 network to the 192.168.1.0/24 network if a link-state routing protocol was in use?
• BOS -> ORL -> JAX -> ATL because this path is the lowest cost

13. Which database or table must be identical on all link-state routers within an area in order to construct an accurate SPF tree?
• link-state database

14. Which two routing protocols use Dijkstra’s shortest path first algorithm? (Choose two.)
• IS-IS
• OSPF

15. When are link-state packets sent to neighbors?
• when a link goes up or down

16. Refer to the exhibit. What does JAX do with link-state packets from ORL?
• sends out the individual link-state packets out the interface connected to BOS

17. A new network administrator is given the task of selecting an appropriate dynamic routing protocol for a software development company. The company has over 100 routers, uses CIDR and VLSM, requires fast convergence, and uses both Cisco and non-Cisco equipment. Which routing protocol is appropriate for this company?
• OSPF

18. What action does a link-state router take immediately upon receipt of an LSP from a neighboring router?
• floods the LSP to neighbors

19. Refer to the exhibit. If all routers and interfaces are configured to use a link-state routing protocol, from which routers will router D receive hello packets?
• B and C

1. What two actions will the EIGRP DUAL FSM take if a link to a network goes down? (Choose two.)
• put the route into passive mode
• query neighbors for a new route
• search routing table for a feasible successor
• run the SPF algorithm to find a new successor
• search topology table for a feasible successor

2. Host 192.168.1.66 in the network illustrated is unable to ping host 192.168.1.130. How must EIGRP be configured to
enable connectivity between the two hosts? (Choose two.)
• R1(config-router)# network 192.168.1.128
• R1(config-router)# auto-summary
• R1(config-router)# no auto-summary
• R2(config-router)# no auto-summary
• R2(config-router)# auto-summary
• R2(config-router)# network 192.168.1.64

3. Refer to the exhibit. The company is using EIGRP with an autonomous system number of 10. Pings between
hosts on networks that are connected to router A and those that are connected to router B are successful.
However, users on the 192.168.3.0 network are unable to reach users on the 192.168.1.32 network. What is the
most likely cause of this problem?
• IP classless is enabled and is causing the packet to drop.
• The command network 192.168.1.32 was not issued on router C.
• The routers are not configured in the same EIGRP routing domain.
• Automatic summarization of the networks is causing the subnetted routes to be dropped.

4. What information is maintained in the EIGRP topology database for a destination route? (Choose three.)
• the routing protocol
• the feasible distance of the route
• the highest cost of the route
• the SRTT value for the route
• the route cost as advertised by the neighboring router
• the physical address of the gateway interface

5. On a router running EIGRP, what database would maintain a list of feasible successors?
• routing table
• neighbor table
• topology table
• adjacency table
6. Refer to the exhibit. What is indicated by the P at the beginning of the topology entry?
• the route is in a stable state
• the route is a preferred route
• DUAL is searching for a better route to this destination
• the exit interface is in passive mode and EIGRP advertisements are blocked

7. In the command router eigrp 20, what is the purpose of the number 20?
• specifies the administrative distance for all EIGRP routes
• identifies the autonomous system number this EIGRP process will advertise
• determines what metric is added to all advertised routes
• indicates the number of addresses in the EIGRP routing domain

8. Refer to the exhibit. In the topology table, what do the numbers 3011840 and 3128695 represent?
• the route metric that is applied to those EIGRP routes for this router
• the trustworthiness of the routing information source
• the composite of the hop count and bandwidth to that destination network
• the total metric for that network as advertised by the EIGRP neighbor

9. Which two statements describe characteristics of EIGRP? (Choose two.)
• EIGRP is a distance vector routing protocol.
• EIGRP supports classless routing and VLSM.
• EIGRP is classified as a link-state routing protocol.
• EIGRP uses TCP for reliable delivery of EIGRP update packets.
• With EIGRP, loop-free paths are achieved through the use of hold-down timers.
• EIGRP sends a periodic update every 30 minutes.

10. Refer to the exhibit. Network 192.168.0.0/28 goes down. What type of packet does Router2 immediately send
to Router1 and Router3?
• a query for network 192.168.0.0/28
• an acknowledgment packet to 224.0.0.9
• an update packet that is sent to 255.255.255.255
• a packet that contains the new routing table for R2
• unicast update packets to 192.168.1.1 and 192.168.2.1

11. Refer to the exhibit. Network 192.168.0.0/28 goes down. What type of packet does Router2 immediately send
to Router1 and Router3?
• a query for network 192.168.0.0/28
• an acknowledgment packet to 224.0.0.9
• an update packet that is sent to 255.255.255.255
• a packet that contains the new routing table for R2
• unicast update packets to 192.168.1.1 and 192.168.2.1

12. What administrative distance would a router assign to a default route in EIGRP that is learned from a source
external to the autonomous system?
• 1
• 5
• 70
• 90
• 170
• 190

13. In which of the following tables does the EIGRP DUAL algorithm store the primary route to a destination?
(Choose two.)
• routing
• topology
• neighbor
• path
• shortest path

14. Which of the following types of routes will be denoted by EX in EIGRP routing table entries? (Choose two.)
• routes learned from other routing protocols
• routes learned from any non-adjacent EIGRP routers
• any route with a hop count metric higher than 224
• EIGRP routes that originate in different autonomous systems
• all passive routes in the routing table

15. Which term defines a collection of networks under the administrative control of a single entity that presents a
common routing policy to the Internet?
• autonomous system
• contiguous networks
• process ID
• BGP

16. Refer to the exhibit. EIGRP is the only routing protocol enabled on this network. No static routes are c
on this router. What can be concluded about network 198.18.1.0/24 from the exhibited output?
• A route to network 198.18.1.0/24 is not listed in the routing table.
• Packets that are destined for 198.18.1.0/24 will be forwarded to 198.18.10.6.
• EIGRP will perform equal cost load balancing across two paths when forwarding packets to 198.18

17. The router with interface 172.16.3.2 is a successor for network 198.18.1.0/24.
Refer to the exhibit. All interfaces have been configured with the bandwidths that are shown in the example
Assuming that all routers are using a default configuration of EIGRP as their routing protocol, what
packets take from the 172.16.1.0/16 network to the 192.168.200.0/24 network?
• A,B,E
• A,C,E
• A,D,E
• Packets will load balance across the A,B,E and A,C,E paths.
• Packets will load balance across the A,B,E and A,D,E paths.
• Packets will load balance across the A,C,E and A,D,E paths.

18. By default, which two metrics are used by EIGRP to determine the best path between networks?
• MTU
• load
• delay
• bandwidth
• reliability

19. Which of the following statements describes the bounded updates used by EIGRP?
Bounded updates are sent to all routers within an autonomous system.
• Partial updates are sent only to routers that need the information.
The updates are sent to all routers in the routing table.
Updates are bounded by the routers in the topology table.

20. The show ip eigrp topology command output on a router displays a successor route and a feasible successor
route to network 192.168.1.0/24. In order to reduce processor utilization, what does EIGRP do when the
primary route to this network fails?
• The router sends query packets to all EIGRP neighbors for a better route to network 192.168.1.0/24.
• The DUAL FSM immediately recomputes the algorithm to calculate the next backup route.
• Packets that are destined for network 192.168.1.0/24 are sent out the default gateway instead.
• The backup route to network 192.168.1.0/24 is installed in the routing table.

21. Refer to the exhibit. Based on the output of show ip eigrp neighbors, what are two possible problems with
adjacencies between Router1 and Router2? (Choose two.)
• The routers are configured with different EIGRP process IDs.
• Automatic summarization was disabled.
• The hello timer for R1 was altered.
• The serial interfaces for both routers are in different networks.
• No feasible successors were found.

22. Refer to the exhibit. This is the debug output from 2 directly connected EIGRP routers. They are not
forming an adjacency. What is the cause?
• one router is a non-cisco router
• they have different autonomous-system numbers
• they are using difference sequence numbers
• they are sending incorrect hello types

23. Refer to the exhibit. Which command will advertise the 192.168.1.64/30 network but not the 192.168.1.32
network on router A?
• network 192.168.1.0
• network 192.168.1.0 255.255.255.0
• network 192.168.1.64 0.0.0.3
• network 192.168.1.64 0.0.0.7
• network 192.168.1.64 0.0.0.255